Categories


WiFi 7 click

Product Code: MIKROE-2046

WiFi 7 click
WiFi 7 click
WiFi 7 click
WiFi 7 click

₹3,049.00
GST inclusive



Qty:

Availability: Backorder


Add to Wish List



WiFi 7 click carries the ATWINC1510-MR210PB IEEE 802.11 b/g/n module, specifically optimized for low-power IoT applications. The click is designed to run on a 3.3V power supply. It communicates with the target microcontroller over SPI interface, with additional functionality provided by the following pins on the mikroBUS™ line: PWM, INT, RST.

ATWINC1510-MR210PB features

The ATWINC1510-MR210PB is a low-power consumption 802.11 b/g/n module which is specifically optimized for low-power IoT applications.

The module has a Cortus APS3 32-bit processor. This processor performs many of the MAC functions, including but not limited to association, authentication, power management, security key management, and MSDU aggregation/de-aggregation. In addition, the processor provides flexibility for various modes of operation, such as STA and AP modes.

Module current consumption

The table below describes the current consumption of the ATWINC1510-MR210PB module:

Device state Code rate Output power, dBm Current consumption(1)
IVBATT IVDDIO
ON_Transmit 802.11b 11Mbps 20.5 290mA 22mA
802.11b 11Mbps 19.5 294mA 22mA
802.11g 6Mbps 19.5 292mA 22mA
802.11b 54Mbps 17.5 250mA 22mA
802.11n MCS 0 18.0 244mA 22mA
802.11n MCS 7 15.5 289mA 22mA
ON_Receive 802.11b 1Mbps N/A 52.5mA 22mA
802.11b 11Mbps N/A 52.5mA 22mA
802.11g 6Mbps N/A 55.0mA 22mA
802.11b 54Mbps N/A 57.5mA 22mA
802.11n MCS 0 N/A 54.0mA 22mA
802.11n MCS 7 N/A 58.5mA 22mA
ON_Doze N/A N/A 380µA <3.5µA
Power_Down N/A N/A <0.5µA <3.5µA
 

Additional pins

Additional pins on the WiFi 7 click, besides the ones on the mikroBUS™ line:

Specifications

Type Wi-Fi
Applications Optimized for low power IoT applications
On-board modules ATWINC1510-MR210PB
Key Features IEEE® 802.11 b/g/n 20MHz solution, integrated PCB antenna, supports IEEE 802.11 WEP, WPA, WPA2 Security
Interface SPI,GPIO
Input Voltage 3.3V
Compatibility mikroBUS
Click board size M (42.9 x 25.4 mm)

Pinout diagram

This table shows how the pinout on WiFi 7 click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes Pin Mikrobus logo.png Pin Notes
  NC 1 AN PWM 16 EN Module Enable
Active-Low Hard Reset RST 2 RST INT 15 INT Device Interrupt output
Chip select CS 3 CS TX 14 NC  
SPI Clock SCK 4 SCK RX 13 NC  
SPI Master Input Slave Output MISO 5 MISO SCL 12 NC  
SPI Master Output Slave Input MOSI 6 MOSI SDA 11 NC  
Power supply +3.3V 7 3.3V 5V 10 NC  
Ground GND 8 GND GND 9 GND Ground

Programming

Code examples for WiFi 7 click, written for MikroElektronika hardware and compilers are available on Libstock.

Code snippet

The following code snippet shows the default main function for all examples.

01 void main(void)
02 {
03     systemInit();
04     printf("Project built for Click Boardrn");
05     printf("Starting driver initialization...rn");
06     
07     hal_wifi7_init();
08     m2m_wifi_init();
09     while (1)
10     {
11         ApplicationTask();
12         m2m_wifi_task();
13     }
14 }

Downloads

 mikroBUS™ Standard specification 

 ATWINC1510-MR210PB datasheet

 WiFi 7 click schematic

 LibStock: WiFi 7 click library 

Write a review
Your Name:


Your Review:
Note: HTML is not translated!
Rating:
Bad           Good

Enter the code in the box below:


Tags: WiFi, 7, click, MIKROE, 2046,

© 2024, MG Automation Technologies. Powered by MG Super LABS.Find us on Google+
Designed with by