RS485 3 click

How does it work?

The main feature of the RS422/RS485 interface is that the signals can be transmitted and received at distances up to 1200m by using the so-called twisted pairs - basically, the signal and its inverted copy are sent via the twisted pair wires. Because of the length of the twisted pair, it will unavoidably be exposed to the influence of the EMI. The interferences will appear in both wires of the twisted pair equally, but thanks to the opposite polarity of the signals the wires are carrying, the interferences will get canceled at the differential inputs of the SN65HVD31. This way, greater signal communication distances can be achieved than with the regular UART.

RS422/RS485 only specifies electrical characteristics of the transmitter and the receiver. It does not specify or recommend any communications protocol, only the physical layer. The top layer communication protocol of choice can be used, such as the MODBUS or DMX protocols.

To improve the signal stability, RS485 3 click is equipped with the TVS – transient voltage suppression diodes used to protect the circuit from the static electricity discharges and other types of dangerous electrical discharges, that might occur.

There are four onboard screw terminals (RX+, Rx-, Tx+, Tx-) for connecting RS422/RS485 twisted pair cable, along with two screw terminals (GND) for common ground connection.

TX and RX pins should be used for connecting MCU UART interface. Two resistors (R2 and R5) should be unsoldered if using more than two clicks on the RS422/RS485 bus.

Specifications

Pinout diagram

This table shows how the pinout on RS485 3 click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes	Pin					Pin	Notes
	NC	1	AN	PWM	16	NC
	NC	2	RST	INT	15	NC
	NC	3	CS	RX	14	TX	UART transmit data
	NC	4	SCK	TX	13	RX	UART receive data
	NC	5	MISO	SCL	12	NC
	NC	6	MOSI	SDA	11	NC
Power supply	3.3V	7	3.3V	5V	10	NC
Ground	GND	8	GND	GND	9	GND	Ground

RS485 3 click electrical specifications

Onboard settings and indicators

Software support

We provide a demo application for the RS485 3 click on our LibStock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Examples Description

The application is composed of two sections :

• System Initialization - Initializes GPIO pins used for button press detection, and two UART modules: first one used for click and second used for logging.
• Application Task - (Code snippet) Constantly polls the state of GPIO pin used for button press detection. Whenever the press is detected, a predefined message will be sent using RS485 3 click. At the same time, inside the application task, the UART is constantly polled, checking for RS485 3 click activity. Whenever new data on click is received, it will be logged to UART module.

void applicationTask()
{
//SENDS DATA
    if (Button( &GPIOA_IDR , 5, 100, 1 ))
    {
        for (i = 0; i <= 7; i++)
        {
            UART3_Write( SEND_DATA [ i ] );
        }
        UART1_Write_Text("Data sent");
    }

//RECEIVE AND LOG DATA 
    if (UART3_Data_Ready())
    {
        tmp = UART3_Read();
        UART1_Write(tmp);
    }
}

The full application code and ready to use projects can be found on our LibStock page.

Other mikroE Libraries used in this example:

• UART

Additional notes and information

Depending on the development board you are using, you may need USB UART click, USB UART 2 clickor RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.

Downloads

RS485 3 click schematic

 SN65HVD31DR datasheet

 LibStock: RS485 3 click library